Updated October 27, 2026
On an August afternoon at Pierce College in Woodland Hills, right next to Tarzana, the average high is 97.4°F. On a December night, the average low is 42.0°F. If your home has a heat pump, one machine handles both. That’s why heat pump maintenance runs on a different calendar than a furnace or a stand-alone air conditioner. Here’s how often to book a heat pump tune up, what the technician checks, how to change the filter yourself, and what to watch for between visits.
Heat pump maintenance is the routine care that keeps a heat pump heating and cooling efficiently: monthly filter checks and clear airflow at home, plus a technician tune up. The Department of Energy sets the minimum at once a year. Because one unit does both jobs, a spring and a fall visit fit better.
One-liner: Book a spring and a fall heat pump tune up, check the filter monthly, and keep every invoice.
| Stat | What it measures | Source |
| 10% to 25% | Energy use gap, well-maintained vs severely neglected heat pump | U.S. Department of Energy |
| Up to 15 percent | Efficiency loss from airflow problems | ENERGY STAR |
| At least once a year | Minimum professional service | U.S. Department of Energy |
| Every 3 months, or per manufacturer or installer | Filter change interval | U.S. Department of Energy |
| At least 2 feet | Clearance around outdoor unit | Trane |
| 4 to 8 inches above ground | Outdoor unit height | Trane |
| About 15 years, longer with regular maintenance | Heat pump lifespan | Trane |
| 97.4°F | Woodland Hills August average high | NCEI 1991 to 2020 normals |
| 42.0°F | Woodland Hills December average low | NCEI 1991 to 2020 normals |
In short: Have a professional service your heat pump at least once a year. That’s the minimum the U.S. Department of Energy gives. Twice a year fits a heat pump better, with a spring visit for cooling and a fall visit for heating, the schedule ENERGY STAR and Trane both describe.
The Department of Energy says a professional technician should service your heat pump at least once a year. Treat that as the floor, not the schedule. ENERGY STAR’s maintenance checklist calls for pre-season checkups each year, with the cooling system checked in spring and the heating system in fall. In a heat pump home, the cooling system and the heating system are the same unit. Follow that calendar and the heat pump gets checked twice. Trane gives the same advice for its own heat pumps: a dealer checkup twice a year, in fall before winter and in spring before AC season.
So the answer to how often to service a heat pump is two visits., and they aren’t copies of each other.
| Spring visit | Fall visit | |
| Mode it preps | Cooling | Heating |
| Heat pump focus | Outdoor coil cleaned, refrigerant charge measured, condensate drain checked | Reversing valve inspected, defrost control tested, heating and cooling controls checked so they never run at once |
| What a skipped visit risks | Starting peak cooling season with a dirty coil or a clogged drain | A valve or defrost fault showing up on the first cold night |
Trane lists the defrost control as a fall-only check, which is one reason the fall visit isn’t a repeat of the spring one.
For Tarzana homes, book the spring visit before the first long run of hot days and the fall visit before December’s cold nights. ENERGY STAR notes that contractors get busy once summer and winter arrive, so earlier dates are easier to get. Have a gas furnace as backup heat? The fall visit can cover that side too, the same work as our heating maintenance.
In short: A heat pump tune up is a technician visit that measures airflow and refrigerant charge, checks for leaks, tightens electrical connections, tests the controls and cleans what’s dirty. On a heat pump it also covers the reversing valve and the defrost control, two parts an air conditioner doesn’t have.
You can see a dirty filter. You can’t see a low refrigerant charge or a loose terminal. That’s the gap regular heat pump service and maintenance fills, with gauges and a meter. Here’s a heat pump tune-up checklist built from the Department of Energy, ENERGY STAR and Trane’s dealer list.
| Check | Why it matters | Visit |
| Airflow, by measurement | Airflow problems can cut efficiency by up to 15 percent | Both |
| Ducts, filter, blower and indoor coil | Dirt, obstructions and duct leaks cut airflow | Both |
| Refrigerant charge, by measurement, plus a leak check | Too much or too little refrigerant makes the system less efficient | Both |
| Electrical terminals and connections | Loose connections can cause unsafe operation and shorten part life | Both |
| Motors and belts | Lubricated and checked for wear | Both |
| Controls and thermostat | Heating stays off when cooling is called, and the reverse | Both |
| Condensate drain | Checked while the heat pump runs in cooling mode | Spring |
| Outdoor coil and base-pan drain holes | Coil cleaned if dirty, drain holes cleared of debris | Spring |
| Reversing valve (heat pump only) | Switches the unit between heating and cooling | Fall |
| Defrost control (heat pump only) | Clears frost from the outdoor coil in heating mode | Fall |
What makes it a heat pump tune up and not an AC tune up? An air conditioner only cools. A heat pump runs its refrigerant loop in both directions, and the reversing valve does the switching. Bryant’s dealer guidance adds a detail most checklists skip: the technician should run the unit in heat mode and cool mode and check the charge in each, because the right charge differs by mode. Still deciding between systems? Our comparison of AC unit vs. heat pump covers the basics.
A good tune up treats refrigerant as something to measure, not something to top off. The Department of Energy lists both steps: verify the charge by measurement and check for leaks. If the charge reads low, ask where it went before anyone adds more. Refrigerant is also licensed work. EPA rules let only Section 608 certified technicians buy refrigerant for stationary equipment like a home heat pump.
Before the visit, jot down anything new: a rattle or hiss, rooms that won’t reach the setting, a jump in the electric bill. It gives the technician a head start. If the tune up turns up a repair, our heat pump services cover repair for every make and model.
In short: Check the filter once a month and change it at least every 3 months, sooner if your manufacturer or installer says so. A heat pump moves air all year, so a clogged filter costs you in summer and winter alike. The swap itself takes a few steps.
The three sources most homeowners run into give three different numbers:
| Source | Filter guidance |
| U.S. Department of Energy | Clean or change every 3 months, or as the manufacturer or installer recommends |
| Trane | Change every 30 to 90 days |
| Bryant | Check monthly, then replace or clean as needed, especially in peak seasons |
Put them together and the rule is simple. Look monthly, never go past three months. ENERGY STAR explains the stakes: a dirty f